中空玻璃打膠機是中空玻璃生產過程當中不可缺少的一種設備，而在使用中空玻璃打膠機之前也需要對中空玻璃鋁條打膠機進行調試，下面我們就來向您介紹中空玻璃鋁條打膠機的調試方法，讓您可以更加方便的使用這種機械設備。
Insulating glass gluing machine is an indispensable equipment in the production process of insulating glass, and the insulating glass aluminum strip gluing machine also needs to be debugged before using the insulating glass gluing machine. Next, we will introduce you to the debugging method of insulating glass aluminum strip gluing machine, so that you can use this mechanical equipment more conveniently.
打開中空玻璃打膠機的氣泵開關,電源總開關,控制臺開關,在控制臺按手動按鈕,然后在顯示屏上找到原點設定,點擊輔助原點設定,然后點擊頭部原點設定,注意原點設定時避免頭部和輔助吸盤碰撞.設定好之后返回設定玻璃厚度,輸入完以后,點擊設置進入.等命令位置和當前位置數值一致即可。
Turn on the air pump switch, main power switch and console switch of the insulating glass gluing machine, press the manual button on the console, then find the origin setting on the display screen, click the auxiliary origin setting, and then click the head origin setting. Pay attention to avoid the collision between the head and the auxiliary suction cup when setting the origin After setting, return to the setting glass thickness. After inputting, click setting to enter Wait until the command position is consistent with the current position value.

打開一桶膠按鈕,按工作選擇拍膠啟動,在按伐開.此時膠頭已經出膠,等看不見白膠,以混均勻以后按伐關,在按鏈接生產線,此時可以自動打膠.開始打膠要看每條邊每個角打膠是否均勻。
Open a bucket of glue button, press the work selection to start glue shooting, and then press open At this time, the glue head has been out of glue. When the white glue cannot be seen, press the cutting off button after mixing evenly, and then press the link production line. At this time, the glue can be applied automatically When you start gluing, it depends on whether the gluing is uniform on each side and corner.
如果需要調整打膠機的壓力,可以在屏幕上點擊返回找到密封配方,會顯示當前密封壓力,如果每條邊都缺膠,那么可增加壓力,壓力大膠量大,壓力小膠量就小.如果發現某條邊膠量不夠時,在密封配方中會顯示有向上密封,上部密封,向下密封,和下部密封,開始打膠的那條邊就是向上密封,然后順序從上。
If you need to adjust the pressure of the glue applicator, you can click back on the screen to find the sealing formula, and the current sealing pressure will be displayed. If there is a lack of glue on each side, you can increase the pressure. If the pressure is large, the glue quantity is large, and the pressure is small, the glue quantity is small If it is found that the amount of glue on a certain edge is insufficient, the sealing formula will display upward sealing, upper sealing, downward sealing and lower sealing. The edge at the beginning of gluing is upward sealing, and then from top to bottom.
如果發下只有某條邊膠少或膠多時,調整掃描膠量細微調整,數值大膠量就大,數值小膠量就小.然后說下到末端伐關的距離,數值大,膠嘴到末端膠量少,數值小膠量大
If there is only a certain edge with less or more glue, adjust the scanning glue amount and adjust it slightly. If the value is large, the glue amount will be large, and if the value is small, the glue amount will be small Then say the distance from the bottom to the end, the value is large, the glue amount from the glue nozzle to the end is small, the value is small, and the glue amount is large
以上就是為大家介紹的有關雙組份打膠機的詳細介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務http://linshi.jncsjx.com
The above is a detailed introduction to the two-component gluing machine. I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service http://linshi.jncsjx.com