<p id="h9hjj"><mark id="h9hjj"><meter id="h9hjj"></meter></mark></p>
    <address id="h9hjj"></address>
    <form id="h9hjj"></form>

    <address id="h9hjj"><listing id="h9hjj"></listing></address>

    <form id="h9hjj"></form>
    <form id="h9hjj"></form>

            高效氣動雙組份打膠機的打膠

            時間:2018-02-27 來源:http://m.wkrd.com.cn/ 發布人:昌盛機械

              高效氣動雙組份打膠機是集技術生產的中空玻璃密封膠打膠機.
              High efficiency pneumatic double component glue machine is the best technology produced at home and abroad hollow glass sealant glue machine.
              A組分泵和B組分泵膠分別采用氣動系統驅動,采用無觸點電器控制系統控制,換向靈敏可靠,其獨特的方便可調試配比機構,大限度地保證雙組份膠近乎苛刻的配比要求,出膠連續均勻,涂膠效果好,生產高。
              A components and B components of pump pump respectively using pneumatic drive system, electric control system adopts contactless commutation control, sensitive and reliable, its unique convenient adjustable proportioning mechanism to ensure maximum two-component adhesive demanding ratio, glue uniform, good gluing effect, high production efficiency.
              1)操作手動轉閥,將A泵提升至高氣動雙組份打膠機,提升過程中觀察各管路有無拉伸過緊處。
              1) operate the manual transfer valve to lift the A pump to the maximum pneumatic double component glue machine. In the process of lifting, there is no tension in the pipe.

            雙組份打膠機
              2)將膠桶放置在A泵壓膠盤下雙組份打膠機,開啟膠桶雙組份打膠機配件,將其中塑料袋外翻至桶外,膠面塑料片取出。
              2) place the plastic bucket in the two component rubber beating machine under the A pump pressure glue disc, open the plastic bucket double component glue machine accessories, turn the plastic bag to the outside of the barrel, and remove the plastic surface piece.
              3)使A泵壓盤緩慢下降,壓盤入桶時應使其與桶口對準,將壓膠盤排氣口打開雙組份打膠機多少錢,直到壓盤接觸膠面。待壓盤內氣體全部排放完并有少量膠從排氣口溢出時,即可關閉排氣閥。(提升開關保持下壓狀態)
              3) make the A pump pressure plate slow down. When the pressure plate is in the barrel, it should be aligned with the barrel mouth, and will open the exhaust port of the rubber disc to the two components glue machine, until the pressure plate contacts the rubber surface. The exhaust valve can be closed when the gas is completely discharged and a small amount of glue is spilled from the exhaust port. (lift switch keep down pressure state)
              4)開機試打膠:將主泵氣源開關打開,按下膠槍開關,直至A泵里空氣排凈槍口處出膠連續時停止。
              4) open machine test glue: open the main pump gas switch, press the glue gun switch until the air in the A pump is discharged at the mouth of the gun and stops when the glue is continuous.
              本文的精彩內容來自雙組份打膠機詳細內容請點擊我們的官方網站:http://m.wkrd.com.cn謝謝您的到來!
              The wonderful content of this article comes from the detailed content of the double component glue machine, please click on our official website: http://m.wkrd.com.cn thank you for your arrival!

            聯系我們Contact us

            • 咨詢熱線:0531-85717458 13705446998
            • 公司地址: 山東省德州市齊河安頭鄉企巢工業園
            • 掃碼聯系我們:

            截屏,微信識別二維碼

            微信號:13705446998

            // 手机看片久久国产免费